Cartographic Projection
every map is wrong, and by exactly how much
Concept

UTM — where it appears

The worldwide system of sixty transverse Mercator zones, each six degrees wide with a scale factor of 0.9996 on its own central meridian. Its zones are six degrees wide because the transverse Mercator series' error grows steeply with distance from the central meridian.

Named by 19 essays across 5 fields — each of them below, with the objects they name alongside it.

A false origin moves every number and no geometry. British National Grid, drawn twice at the same scale. On the left the coordinates are measured from the projection's own origin, where the central meridian meets the true origin's parallel, and 52% of the country takes a negative easting or northing — the worst reaching -323 km. On the right the authority's published false origin of 400 km east and -100 km north has been applied, and none of them does. Every distance computed from the two sets of numbers agrees to the last bit a double has left after carrying six figures, and every bearing agrees exactly; the only thing that changed is that no coordinate carries a sign. The margins say the origin was fitted to the land rather than placed arbitrarily below it: 77 km spare in the west and 50 m in the south, on a grid 988 km tall.

A grid has an origin that is not there

Every published national grid measures from a point in the sea. The British one sits 400 kilometres west and 100 kilometres south of where the projection's own zero is, and moving it changes every coordinate in the country and not one distance or bearing.

practice · Grid Only one of a grid's five parameters changes the map. The same ground point written on the British National Grid and on UTM zone 31N, with the difference between the two coordinate pairs taken apart. The largest term by four orders of magnitude is where the two grids put zero — 5544 km, being a different central meridian, a different true origin and different false constants, all of which move every coordinate and no distance. The datum, which is the term everybody names, moves the ground 106 m. And the whole geometric difference between two transverse Mercators is their scale factors — 0.9996012717 against 0.9996 — which at this point is 50 cm. Four of a grid's five parameters are bookkeeping; the fifth is the map.

What a grid is made of

A projected coordinate declares five things — a datum, a projection, its parameters, a unit and an axis order — and four of them are invisible in the numbers. Every one has a documented case of being guessed wrong, and the cheapest of those cost a hundred metres.

practice · Grid London to Tokyo, seen four ways. The same two routes on four projections. The gnomonic projection renders every great circle as an exactly straight line, which is what it is for; Mercator renders every rhumb line straight instead. Neither path changed — only the map did.

The aspect is a free choice

A projection's distortion pattern is fixed relative to its own axis, and where that axis points is entirely up to the cartographer. Rotating it is the cheapest available improvement and it is the one most often left unmade.

families · Families The scale factor was chosen, and the choice is a V. The worst departure of the grid scale factor from unity across a region 9° wide and 9° tall, for every scale factor between 0.998108 and 1.0002, on a central meridian of 2°W. A tangent projection touches at one meridian and is too big everywhere else, at 1987 ppm. Scaling the whole grid down slides that interval until it straddles unity, and the minimum sits at 1/√k_max = 0.999008102, where the worst departure is 993 ppm — a factor of 2.00, which is the most this construction can buy and is reached exactly. The published value marked beside it was chosen the same way, for this region, in the 1930s.

The scale factor was chosen

A grid's scale factor is not a constant of nature. Britain's 0.9996012717 is the reciprocal square root of the worst distortion a tangent projection would have had over the country, it halves the worst-case error exactly, and the halving is the most that construction can ever buy.

practice · Grid Transverse Mercator. The graticule of the Transverse Mercator projection at 30° of longitude and 15° of latitude. the only projection on which a constant compass bearing is a straight line. It is conformal.

Transverse Mercator and the series that computes it

The projection most of the world's survey data lives in has no closed form. What every national grid actually computes is a truncated power series in the flattening, and how far it can be trusted is an engineering parameter rather than a property of the projection.

families · Ellipsoid The sixty zones, each six degrees wide. Every zone is a separate transverse Mercator projection about its own central meridian, so the world is covered by sixty maps rather than one. Zone 31 is picked out, running from 0° to 6° with its axis on 3°. Coordinates do not carry across a zone boundary — a point on either side of one has two entirely different eastings, and nothing in the numbers says which zone they belong to.

UTM and the zone system

Sixty separate maps of the world, each six degrees wide, each with a scale factor of 0.9996 chosen so the projection is wrong everywhere and less wrong at the edges. Every constant in the definition is a measured trade rather than a convention.

families · Ellipsoid What changing the datum alone does to a coordinate. The distance on the ground between a point as read on its national datum and the same numbers read on WGS84, computed through the published seven-parameter transformation. The shifts run from 49 to 166 metres. For comparison, the scale error a UTM zone introduces at its edge is under a metre per kilometre — so the datum, which is usually left unstated, dominates the projection, which is usually argued about.

Datum shifts dwarf projection errors

The projection argument is conducted in parts per million and the datum question is answered in hundreds of metres. A coordinate whose datum is unstated is out by more than any projection choice could ever put it, and almost nobody checks.

wrong · Ellipsoid What a grid of one's own is worth. For every candidate central meridian, the best worst-case distortion achievable over the region once the scale factor has also been optimised — so each point on the curve is already the bottom of its own V. The minimum is at 2.9°W with k₀ = 0.9993009, giving 700 ppm. The dashed line is UTM zone 30, whose meridian and scale factor were chosen for no region in particular, at 1059 ppm. The national grid is better by a factor of 1.51 — which is the whole of the answer to why a country publishes a grid rather than using the zones, and it is a smaller factor than the argument is usually made to sound.

Designing a grid for one region

A country with a grid of its own beats the international zone that would otherwise carry it by a factor of 1.51. That is worth having and it is much less than the argument is usually made to sound, and the difference between the two numbers is the whole case for and against national grids.

practice · Grid How large a patch can be treated as flat, at 10 parts per million. The smallest scale distortion any map of a circular patch can have, against the radius of the patch, on logarithmic axes. The line is straight with a slope of 2.00: the error grows as the SQUARE of the size, so a patch ten times wider is a hundred times worse. A tolerance of 10 ppm is reached at a radius of 40.3 km — 81 km across — and that is the number behind the boundary between plane surveying and geodesy.

How small is flat enough

A builder works in plane coordinates and a national mapping agency does not, and the line between them is not a convention. The unavoidable error of treating a patch of the Earth as flat grows as the square of its size, and the size at any stated tolerance is a number.

impossibility · Curvature Both zones are right, and one of each is not. A 20 km baseline straddling the boundary between UTM zones 31 and 32 at 52°N, computed from grid coordinates three ways, on logarithmic bars. Taking both ends in zone 31 and taking both in zone 32 give answers 0 nanometres apart — the resolution a double has left after carrying a six-figure easting rather than a disagreement — so a job may use either and the overlap belt every zone publishes exists to let it. Taking each end from the zone it nominally belongs to gives 392 km, because the two eastings are measured from meridians six degrees apart and subtracting them measures nothing at all. The same ground point is 706 km east in one zone and 294 km east in the other, and both coordinates are correct.

Where two zones meet

A twenty-kilometre baseline across a zone boundary is computed correctly in either zone — the two answers differ by nanometres — and taking one end from each returns 392 kilometres. Both zones are right and the seam between them is not a small error but a category one.

practice · Grid Grid north against true north at 52°, across a 6° zone. seven meridians drawn in the grid's own coordinates. The grid's north is straight up the page everywhere by construction; the meridians are not, and the angle between them is the convergence. It is exactly zero on the central meridian, reaches 2.36° — 142 minutes of arc — at 3° out, and changes sign across the middle. The manual's γ = Δλ sin φ is 3.0″ short of it at the zone edge.

Grid north is not north

A grid has one north, parallel everywhere on the sheet by construction. The Earth has a different one at every point. The angle between them reaches two degrees at the edge of a UTM zone, and a straight line on the grid is not a straight line on the ground either.

families · Ellipsoid The order the corrections go in, and what it costs. Setting out a 51.8 km line on the UTM zone 31N means turning a grid bearing into an azimuth to observe, and there are two corrections: the meridian convergence, 0.8669° here, and the arc-to-chord correction, 6.242″. Each bar carries the lateral offset it produces at the far end of the line, because a bearing error is a number nobody can picture and a sideways miss is the thing that misses. The exact arc-to-chord and the classical formula every manual gives differ by 0.0044″, which is 1.10 mm at the far end — small, real, and the reason the corrections have an order rather than a sum.

Setting out runs the chain backwards

Turning a design coordinate into something to observe on the ground means undoing the reduction chain, and undoing a chain reverses the order as well as the operations. Two of the corrections do not commute, and getting them the wrong way round misses by a millimetre at fifty kilometres.

practice · Reduction The two reductions, at a grid factor of 1.0004. A measurement made on the ground has to be brought to the ellipsoid and then to the grid, and the two corrections have opposite signs. The elevation factor is R/(R+h) and always shrinks; the grid factor here is 1.0004, which stretches. Their product is the only number a surveyor can use. They cancel exactly at 2551 metres. At 1500 metres the combined factor is 165 parts per million, which is 1.65 metres on a 10 kilometre baseline.

The ground is not the grid

A tape measure on a hillside has to be brought down to the ellipsoid and then out onto the map, and the two corrections have opposite signs. On a grid whose scale factor exceeds one there is exactly one elevation where they cancel — 2,551 metres, for a factor of 1.0004.

datums · Height Only one of a grid's five parameters changes the map. The same ground point written on the British National Grid and on UTM zone 31N, with the difference between the two coordinate pairs taken apart. The largest term by four orders of magnitude is where the two grids put zero — 5544 km, being a different central meridian, a different true origin and different false constants, all of which move every coordinate and no distance. The datum, which is the term everybody names, moves the ground 106 m. And the whole geometric difference between two transverse Mercators is their scale factors — 0.9996012717 against 0.9996 — which at this point is 50 cm. Four of a grid's five parameters are bookkeeping; the fifth is the map.

Two grids over the same ground

One point in the English Midlands is 406,788 east on the British grid and 167,478 east on UTM. Separating the difference properly leaves a surprise — only one of a grid's five parameters changes the map, and it is not any of the four that dominate the number.

practice · Reduction The boundary of the region the series is the map in. The curve where the transverse coordinate reaches 2.918, which is where the terms stop shrinking. It crosses the equator 83.81° from the central meridian and closes towards the poles, because the same longitude is a smaller transverse coordinate at a higher latitude — the boundary is a curve rather than a meridian. The narrow band beside it is a 3° zone, the width national grids actually use, drawn to the same scale: the practical world sits in about a fiftieth of what the series can reach. Drawn in Mollweide.

Where the series stops being the map

The transverse Mercator has no closed form on an ellipsoid, so every national grid computes a truncated series. Asking how many terms it needs has an answer everywhere; asking whether more terms always help has an answer only within 83.81° of the central meridian, and the boundary is computed rather than assumed.

families · Ellipsoid The widest zone a tolerance of 690 parts per million allows. At each latitude, the half-width at which a transverse Mercator grid with its scale factor rebalanced for that width reaches 690 ppm at its worst point. That tolerance is the one UTM actually meets at the equator, so the curve passes through UTM's own 3° there — and rises to 37.0° at 85° north, because a degree of longitude covers cos φ of the ground and the scale error goes as the square of the ground width. Six degrees is the answer at one latitude.

Sixty zones was a decision about one latitude

Twelve rungs price a grid, a zone, an origin and a reference, and every one of them works inside a single zone. The number of zones has never been asked about: six degrees meets its tolerance at the equator and is loose everywhere else, so a system spending the same tolerance evenly would use 51 zones at the equator and 8 at 82° — and UTM's worst error is 981 parts per million, not the 400 always quoted.

practice · Grid

A grid reference names a square

This ladder has priced everything about a grid except how a coordinate on it is written. A grid reference is truncated rather than rounded, so it names the south-west corner of a square rather than a point in it — and a population of references is displaced half a cell each way, which is a bias rather than scatter and does not average out.

practice · Grid

Further north on the grid is not further north

Thirteen rungs price a grid's origin, scale, units and zones, and every one treats a coordinate as a position. It is also an ordering, and the two disagree: a parallel climbs 4,379 metres of northing on its way to the edge of a UTM zone, so two places 4.4 kilometres apart in latitude can be listed in the wrong order — and the share of pairs it happens to is the convergence, in a different unit.

practice · Grid

One pair of numbers, a hundred and twenty places

A UTM coordinate is two numbers and a zone. Drop the zone and the numbers are still valid in each of the sixty; drop the hemisphere too and the pair names a hundred and twenty places. They form two rings at one latitude each, spaced exactly six degrees apart, and every one of them has the same grid convergence and the same scale factor — so no further geometric measurement can choose between them.

practice · Grid

Named alongside it

The objects these essays reach for when they reach for this one.

National GridZoneScale factorTransverse MercatorToleranceCentral meridianConventionConvergenceBoundaryFalse originDatumCoordinate reference system

All concepts