Cartographic Projection
every map is wrong, and by exactly how much
Figure

Four steps between a tape and a drawing

Drawn here at the parameters it defaults to, with every essay that calls it.
Four steps between a tape and a drawing. A slope distance of 76.895 km measured at 3.2° on ground 220 m above sea level, reduced to the British National Grid, with every step drawn on a logarithmic scale in millimetres. The slope reduction is the largest by a wide margin at 119.90 m and is the one everybody applies. The grid reduction is 30.23 m. The fourth bar is not a step at all: it is what using the levelled height where the height above the ellipsoid is wanted costs, with a geoid separation of 48.5 m — 583 mm, which is 1.9% of the grid reduction it sits beside and 29 times the tolerance the job closes to. Reading a correction's importance off its share of the chain is how it gets dropped.

A slope distance of 76.895 km measured at 3.2° on ground 220 m above sea level, reduced to the British National Grid, with every step drawn on a logarithmic scale in millimetres. The slope reduction is the largest by a wide margin at 119.90 m and is the one everybody applies. The grid reduction is 30.23 m. The fourth bar is not a step at all: it is what using the levelled height where the height above the ellipsoid is wanted costs, with a geoid separation of 48.5 m — 583 mm, which is 1.9% of the grid reduction it sits beside and 29 times the tolerance the job closes to. Reading a correction's importance off its share of the chain is how it gets dropped.

It is drawn by survey-figure with show: "reduction-chain" — one member of a family of 16 figures that share a generator, so the drawing above is what that generator returns when it is asked for this one and given nothing else.

11 essays call it. Every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the one its essay argues about.

Where it is called

Changing this changes every one of these figures.

A false origin moves every number and no geometry. British National Grid, drawn twice at the same scale. On the left the coordinates are measured from the projection's own origin, where the central meridian meets the true origin's parallel, and 52% of the country takes a negative easting or northing — the worst reaching -323 km. On the right the authority's published false origin of 400 km east and -100 km north has been applied, and none of them does. Every distance computed from the two sets of numbers agrees to the last bit a double has left after carrying six figures, and every bearing agrees exactly; the only thing that changed is that no coordinate carries a sign. The margins say the origin was fitted to the land rather than placed arbitrarily below it: 77 km spare in the west and 50 m in the south, on a grid 988 km tall. Grids, and what a survey does

A grid has an origin that is not there

Every published national grid measures from a point in the sea. The British one sits 400 kilometres west and 100 kilometres south of where the projection's own zero is, and moving it changes every coordinate in the country and not one distance or bearing.

 A scale factor is a property of a point, and a distance is not. The grid scale factor sampled along a 362 km line on the British National Grid at a bearing of 90°, with the three rules in use drawn as the constants they replace it by. In a transverse Mercator k depends on the easting almost alone and goes as its square, so along an east–west line the curve is very nearly a parabola. The endpoint mean is the chord across it and lands 268.6 ppm high, which is 97.3 m over this line. Simpson's rule integrates a parabola exactly and lands 0.004 ppm out — 1.3 mm. Neither number is about the line's length. Grids, and what a survey does

The scale factor of a line

A scale factor is a property of a point and a distance is not measured at a point. The three rules in use for averaging one along a line differ by a hundred metres on a 362-kilometre baseline, and which of them is adequate is decided by the line's direction rather than its length.

 Two feet, and the one that is not a rounding. The US survey foot is 1200/3937 m and the international foot is exactly 0.3048 m, so the first is longer by 2.0000 parts per million. Read a coordinate in the wrong one and the error is proportional to the coordinate, not to any distance in the job: at 2.5 million feet from the false origin it reaches 1.52 m, and it crosses a survey's own closing tolerance of twenty millimetres at 33 thousand feet. Across a 300-foot site the same mistake changes every dimension by 0.18 mm — below every tolerance there is, which is why a plan in the wrong foot passes every check and is in the wrong place. Grids, and what a survey does

The units are part of the coordinate

Two feet were in use in the United States until 2022, differing by exactly two parts per million. A plan drawn in the wrong one has every dimension right to a fifth of a millimetre and sits three-quarters of a metre from where it belongs, which is why it passes every check anybody runs.

 Both zones are right, and one of each is not. A 20 km baseline straddling the boundary between UTM zones 31 and 32 at 52°N, computed from grid coordinates three ways, on logarithmic bars. Taking both ends in zone 31 and taking both in zone 32 give answers 0 nanometres apart — the resolution a double has left after carrying a six-figure easting rather than a disagreement — so a job may use either and the overlap belt every zone publishes exists to let it. Taking each end from the zone it nominally belongs to gives 392 km, because the two eastings are measured from meridians six degrees apart and subtracting them measures nothing at all. The same ground point is 706 km east in one zone and 294 km east in the other, and both coordinates are correct. Grids, and what a survey does

Where two zones meet

A twenty-kilometre baseline across a zone boundary is computed correctly in either zone — the two answers differ by nanometres — and taking one end from each returns 392 kilometres. Both zones are right and the seam between them is not a small error but a category one.

 A grid scaled to the ground, and where it stops being one. A surface coordinate system on the British National Grid: the grid multiplied by 1.0004044, the reciprocal of the combined factor at a project origin 120 m above the ellipsoid, so that a grid distance equals a ground distance there. It is exact at the origin by construction and wrong everywhere else, and the two directions are not comparable — the axis is logarithmic across five decades. 60 km due east the set-out distance is out by 5559 mm, and the same distance due north by 20.5 mm. The scale factor of a transverse Mercator depends on the easting and almost not at all on the northing, so a system sold as good "within a few kilometres" has a useful area that is a strip rather than a circle. Grids, and what a survey does

A grid scaled to the ground is not a map

Construction sites work in coordinates where a tape reading equals a computed distance, which is achieved by multiplying the national grid by a constant. The result is exact at one point, degrades east–west forty times faster than north–south, and is not a map projection at all.

 Four steps between a tape and a drawing. A slope distance of 76.895 km measured at 3.2° on ground 220 m above sea level, reduced to the British National Grid, with every step drawn on a logarithmic scale in millimetres. The slope reduction is the largest by a wide margin at 119.90 m and is the one everybody applies. The grid reduction is 30.23 m. The fourth bar is not a step at all: it is what using the levelled height where the height above the ellipsoid is wanted costs, with a geoid separation of 48.5 m — 583 mm, which is 1.9% of the grid reduction it sits beside and 29 times the tolerance the job closes to. Reading a correction's importance off its share of the chain is how it gets dropped. Grids, and what a survey does

What a tape measures

Four steps stand between an instrument reading and a coordinate, and their sizes are not in the order anybody expects. On a 77-kilometre line the slope reduction is 120 metres, the grid reduction 30, and a step nobody names — using the height above sea level where the height above the ellipsoid is wanted — is 583 millimetres.

 A closed traverse cannot see a scale error. The same closed figure with two different errors in it. On the left every leg is 400 parts per million too long, which is roughly what forgetting the grid scale factor costs — and the figure closes to 2.3e-13 m, which is the last bit of a double rather than a measurement. Scaling every leg of a closed figure by the same factor produces a similar figure and a similar figure is still closed, so the check every specification leans on is blind to it. Every dimension in that figure is wrong: the perimeter is out by 1.17 m. On the right one angle is 20 seconds out — a far smaller disturbance in its own units — and the figure fails to close by 0.062 m. Closure tests the shape and says nothing about the size. Grids, and what a survey does

A traverse must close

The check every survey specification leans on cannot see the error this whole field is about. Scale every leg of a closed figure by four hundred parts per million and it closes to the last bit of a double, while every dimension in it is wrong.

 Two conventions, and neither of them finds the blunder. A blunder of 350 mm added to leg 3 of a closed traverse, producing a misclosure of 350 mm — one part in 8344, which most specifications would accept. Bowditch's rule shares the misclosure out in proportion to leg length; the Transit rule shares it in proportion to each leg's component along the axis being corrected. Both close the figure exactly, so both are valid; they disagree with each other by up to 14 mm; and neither puts more than 104 mm of correction on the leg that is actually wrong. A rule for distributing a misclosure is a convention for producing consistent numbers, and it is not an instrument for finding errors. Grids, and what a survey does

The two ways to spread a misclosure

Bowditch's rule and the Transit rule take the same closed figure and the same misclosure and disagree about which legs were wrong. Both close it exactly, neither puts the correction on the leg that actually carries the blunder, and no measurement can settle which is right.

 Which corrections a 10 mm job may leave out. Each correction inverted: the line length — or, for the last row, the patch radius — at which that correction alone reaches 10 mm, for a job 150 m above the ellipsoid on 2° of ground, 0.0° from the British National Grid's central meridian. The tightest is the slope reduction at 16 m. Three of the four rows are linear in the tolerance, so this ranking is the same at a millimetre and at a decimetre; what does change it is the site — move the job up a mountain or onto steeper ground and the order is different, which is why a specification's list is not transferable. Grids, and what a survey does

The tolerance decides the model

Every correction inverts to a distance — the line length at which it alone exceeds a stated tolerance. The ranking those distances produce is the same at a millimetre and at a decimetre, and it is different for two jobs at the same tolerance on different ground.

 What a 20 mm closure tolerance lets each station hide. A closed traverse of seven stations in plan, each labelled with the angle blunder that would leave the closure inside a 20 millimetre tolerance. An angle error at a station rotates everything downstream of it about that station, so the closing point moves by the distance from the station to the close — and the last station before the close stands 72 metres from it and can hide 57 arcseconds, against 2.1 at the worst-placed station. The check is not insensitive; it is unevenly sensitive, and nothing in the specification says so. Grids, and what a survey does

What a closed figure cannot see

A closed traverse imposes exactly two conditions on its observations, so everything else is free — and the freedom is not spread evenly. At a twenty-millimetre tolerance the worst-placed station in a seven-station loop hides an angle blunder of 2.1 arcseconds and the station standing seventy-two metres from the close hides 57, because a rotation about a point near the finish moves the finish hardly at all.

 Two routes to one grid distance, 76.7 kilometres apart. The first four bars are the tape's chain: the chord between two marks, the height difference taken off it, the reduction to the ellipsoid, and the projection's own scale applied. The last is the satellite route — project both marks and subtract — which needs none of those steps because the observation already contains the positions the chain exists to supply. They agree to 0.17 millimetres, and that agreement is what makes the chain checkable at all: two routes to one number, sharing no arithmetic. Grids, and what a survey does

The chain the satellite does not have

The four-step reduction from a tape reading to a grid coordinate exists because a tape does not know where it is. A satellite observation does, so the same distance can be got by projecting both ends and subtracting — and the two answers agreeing to a fifth of a millimetre is the first check the chain has ever had.

The whole library