Cartographic Projection
every map is wrong, and by exactly how much
Figure

Normal gravity, derived from four constants

Drawn here at the parameters it defaults to, with every essay that calls it.
Normal gravity, derived from four constants. Gravity on the surface of the level ellipsoid, by Somigliana's closed form, for WGS84. Nothing here is measured: a, f, GM and ω go in and the whole curve comes out, rising 5186 milligal — 0.53 per cent — from equator to pole. The two open marks are the published values of equatorial and polar gravity for WGS84, which the derivation reproduces to ten significant figures rather than borrowing.

Gravity on the surface of the level ellipsoid, by Somigliana's closed form, for WGS84. Nothing here is measured: a, f, GM and ω go in and the whole curve comes out, rising 5186 milligal — 0.53 per cent — from equator to pole. The two open marks are the published values of equatorial and polar gravity for WGS84, which the derivation reproduces to ten significant figures rather than borrowing.

It is drawn by height-figure with show: "gravity-profile" — one member of a family of 8 figures that share a generator, so the drawing above is what that generator returns when it is asked for this one and given nothing else.

11 essays call it. Every call below passes it something, because a placement that passes nothing draws whichever member of the family the generator happens to default to rather than the one its essay argues about.

Where it is called

Changing this changes every one of these figures.

Three surfaces, and the two heights between them. The ellipsoid, the geoid and the ground, with the two heights a coordinate can carry. Ellipsoidal height h is what a satellite fix returns and is measured from a surface defined by four constants. Orthometric height H is what a level and a staff measure and is referred to the geoid — the equipotential surface that best fits mean sea level. They differ by the separation N, drawn here as 45 metres because that is a stated input rather than a computed one: a geoid model is a data product with a truncation degree in it, and this site computes rather than downloads. The arithmetic h = H + N is exact whatever N is. What the numbers refer to

Height above what?

A satellite reports a height above a mathematical surface. A level and a staff report a height above the surface water settles on. The two disagree by tens of metres, both are correct, and only one of them decides which way a pipe drains.

 Normal gravity, derived from four constants. Gravity on the surface of the level ellipsoid, by Somigliana's closed form, for WGS84. Nothing here is measured: a, f, GM and ω go in and the whole curve comes out, rising 5186 milligal — 0.53 per cent — from equator to pole. The two open marks are the published values of equatorial and polar gravity for WGS84, which the derivation reproduces to ten significant figures rather than borrowing. What the numbers refer to

The ellipsoid is a level surface

WGS84 publishes two dozen constants and defines four of them. The other twenty are consequences — polar gravity, the potential of the ellipsoid, the coefficient that dominates the Earth's gravity field — and every one comes back here from a, f, GM and ω to the last digit published.

 Why a levelled height is not a distance. The correction between raw levelling and orthometric height, for lines at 200, 500, 1000, 2000 metres above the geoid running north from 50°. It is not instrument error: level surfaces converge towards the pole, so a run that stays on one of them gains height relative to another. A line 2000 metres up reaches 647 millimetres over 400 kilometres. The dashed line is 10 millimetres, which is about what a first-order levelling network closes to over that distance — so this is not a refinement, it is the larger of the two numbers. What the numbers refer to

A levelled height is not a distance

Level surfaces converge towards the poles by five metres in a thousand, so a chain of perfectly executed levelling observations does not sum to a height difference. The correction over four hundred kilometres of northing is larger than the network's own closure.

 A deflection of 10 arcseconds, and what it hides. The ellipsoid normal and the plumb line at one point, with the geoid tilted against the ellipsoid by 10 arcseconds — drawn 3000× steeper than life, because at true scale the two lines are indistinguishable. The relation is exact and linear: an arcsecond of deflection is the geoid rising 4.85 millimetres in a kilometre, so 10 arcseconds is 48.5 millimetres per kilometre. A star sight measures the plumb line's direction, so astronomic latitude differs from geodetic by exactly this angle — 309 metres of ground, at a point where the coordinate itself is correct. What the numbers refer to

The plumb line is not the normal

A latitude measured from the stars and a latitude that means a position on the ellipsoid are different angles, because a plumb bob hangs along gravity and gravity is not perpendicular to a mathematical surface. Ten arcseconds of difference is 309 metres of ground.

 Clairaut's theorem, and the term it drops. Clairaut's theorem says the flattening of a rotating body plus the flattening of the gravity on it equals five halves of the ratio of centrifugal to gravitational acceleration at the equator. Measured on WGS84: f = 3.3528e-3, f* = 5.3024e-3, and their sum is 8.65525e-3 against the theorem's 8.62447e-3. The residual is 3.08e-5, which is 2.74 times f² — second order, which is what a first-order theorem is entitled to be wrong by. What the numbers refer to

The flattening is not a free parameter

An ellipsoid is usually presented as two numbers somebody fitted. One of them is not free — Clairaut's theorem relates the shape of a rotating body to the gravity on it, and the relation holds on WGS84 with a residual of 3.1×10⁻⁵ — which is 2.74 times f², exactly what a first-order theorem is entitled to.

 One level surface, 1000 m up at the equator, in two height systems. A single equipotential surface — the shape a body of water takes — with the number each height system gives it, all the way from the equator to the pole. The orthometric height, which is the distance up the plumb line and therefore a length, falls by 5.28 metres along it, because level surfaces converge polewards. The dynamic height, which is the geopotential number divided by one constant gravity value, is flat to 0.000 millimetres — it is the same number everywhere on the surface, and it is not a distance from anything. What the numbers refer to

A height that is not a length

Level surfaces converge polewards, so the surface a lake sits on is 5.28 metres lower at the pole than at the equator and a height system that reports lengths says a lake runs downhill. The fix reports a number that is constant on the surface and is not a distance from anything: a hundred-metre climb raises it by 99.73 metres at the equator and 100.26 at the pole.

 Shape predicted from field, against shape as published. Clairaut's theorem gives a body's flattening from two numbers of its gravity field: J₂, which is how its mass is arranged, and m = ω²a³/GM, which is how fast it spins. For a body in hydrostatic equilibrium the prediction is the shape, and the diagonal is where such a body sits. Earth is on it to 0.05 per cent — 12 metres at the pole, out of twenty-one kilometres of flattening. Mars is 12.5 per cent off it, which is 2.23 kilometres, and the excess is Tharsis: a body carrying a continent-sized volcanic load is not a fluid figure, so its ellipsoid is not one of its own level surfaces, and its zero of height has to be chosen rather than found. What the numbers refer to

A body with no sea level

On Earth the zero of height is found rather than chosen — water settles onto the equipotential surface by itself. Nowhere else has one, and the difference is measurable: Clairaut's theorem predicts the Earth's flattening from its own gravity field to twelve metres at the pole and misses Mars's by 2.2 kilometres.

 The height of a 4000-metre summit, against the density assumed beneath it. The geopotential number is 39204 m² s⁻² and is not in doubt. Turning it into a length divides it by the mean gravity along the plumb line, which is inside the mountain — and reconstructing that from the gravity measured at the surface needs a density. Taking the rock to be 2400 rather than the 2670 it actually is puts the summit 185 mm low; taking it to be 2900 puts it 157 mm high. Skipping the reduction entirely puts it 691 mm high, which is why the reduction exists. What the numbers refer to

The line a height is measured along

Five rungs have argued about the surface a height is measured *from* and every one of them took the line it is measured *along* to be straight and known. It is neither: through a stated buried mass a plumb line arrives 47 millimetres from the point below the summit, and the height it gives depends on the density of rock nobody has seen — 342 millimetres of spread at 4,000 metres and 1.37 metres at 8,000.

 The drift is a straight line in the deflection. The horizontal distance between where a plumb line hangs at the top of a column of rock and where it hangs at the bottom, against the deflection of the vertical the mass produces at the surface. Four heights of column. Every line is straight through the origin: 12.54 mm of drift per arcsecond of deflection over a 4,000 m line, to two parts in ten thousand across a fortyfold range of deflection. Which is what makes the number transferable — the 47 mm the ladder started from was a statement about one buried sphere, and this is a statement about any mass that produces the same deflection. What the numbers refer to

How far the plumb line bends

The previous rung dropped a plumb line down a four-kilometre column of rock beside one buried mass and found it arrived 47 millimetres from the point below the summit. That is a number about that mass. Parameterising by the deflection of the vertical instead — the quantity surveyors actually measure — gives 12.54 mm per arcsecond, exactly linear across a fortyfold range.

 What a geoid model leaves out, against the degree it stops at. The RMS of everything above the model's highest degree, from Kaula's rule — the statement that the normalised coefficients at degree n are about 10⁻⁵/n². The line is R × 10⁻⁵ ÷ n, so a model to degree 360 omits 17.7 centimetres and one to 2190 omits 2.9. Every orthometric height derived from such a model carries that as an error, and it is not quoted with the height. What the numbers refer to

The geoid model stops at a degree

Eleven essays treat the geoid as a surface that exists. Every geoid anybody uses is a series truncated at a degree, so every orthometric height derived from one carries an omission error nobody quotes with the height — eighteen centimetres at degree 360 — and the same truncation removes two thirds of the slope, which does not converge at all.

 The same baseline, turned. The part of a 20 km height difference a degree-360 geoid model omits, against the direction the baseline runs, at four anisotropy ratios. A ratio of one is the model rung 9 used and is a flat line — the isotropic covariance cannot depend on a direction, by construction, which is the whole of the objection. At a ratio of two the same baseline omits 165 millimetres along the grain and 241 across it. What the numbers refer to

The correlation is not the same in every direction

Every number in the previous rung came out of Σ cₙ Pₙ(cos ψ) — a covariance that depends on the angular distance and nothing else. Ground has grain: at a modest anisotropy the same 20 km baseline omits 165 millimetres along it and 241 across, and the isotropic answer understates the worse direction by 18.4 per cent.

The whole library